๐Ÿ“– This is a static documentation page. Open the interactive version with live canvas demos โ†’

Microelement Recipes

Practical patterns for combining microelements into real work sequences. Each recipe shows a concrete production scenario and the exact microelements to use.


Pick and place

Scenario โ€” a worker picks a part from a bin and places it into a fixture.

  • Reach by hand โ€” to the bin, ~400 mm, medium degree of control
  • Take / Grasp โ€” simple take, without caution
  • Move โ€” to the fixture, ~300 mm, mass < 1 kg
  • Install / Place โ€” on shaft, medium degree of orientation

If the bin is cluttered, raise the degree of control quality factor on Reach and Grasp โ€” this correctly inflates the time to reflect search effort.


Fasten with a hand tool

Scenario โ€” tighten a bolt using a torque wrench.

  • Reach by hand โ€” to the wrench, ~500 mm
  • Take / Grasp โ€” intercept grip
  • Move โ€” to the bolt, ~200 mm, mass 0.8 kg
  • Install / Place โ€” onto bolt head, high degree of orientation
  • Rotate โ€” tighten, 360ยฐ, thread diameter 10 mm
  • Press by hand โ€” final torque, 25 Nm
  • Disconnect / Disengage โ€” wrench off bolt, tight connection
  • Release โ€” place wrench on bench

Set quality factor convenience of work to "inconvenient" if the bolt is below table level.


Visual inspection

Scenario โ€” operator visually checks a welded seam.

  • Take a look โ€” focus on the seam, ~600 mm
  • Gaze โ€” scan the length of the seam, distance proportional to length
  • Walk โ€” if the seam extends beyond arm's reach, walk along it

No grasping, no force โ€” body motions and eye actions only. Set the Action's Purpose tag to Inspection and Flow tag to Supporting.


Pedal operation

Scenario โ€” activate a press brake foot pedal.

  • Move leg โ€” foot to pedal position
  • Press by leg โ€” actuate pedal, 80 N

If the pedal requires repeated strokes, use the microelement multiplier instead of duplicating elements.


Cut a wire to size

Scenario โ€” measure, mark, and cut a cable harness wire.

  • Reach by hand โ€” to the wire spool, ~600 mm
  • Take / Grasp โ€” grasp wire end
  • Move โ€” pull wire to the measuring ruler, ~800 mm
  • Take a look โ€” verify the mark, ~300 mm
  • Set on size โ€” align the wire to the cut mark
  • Press by hand โ€” squeeze side cutters, 15 N
  • Release โ€” drop the cut piece into a tray

Set on size is the precision microelement โ€” use it whenever exact positioning by sight matters.


Posture changes during heavy assembly

Scenario โ€” a worker installs a floor-level bracket.

  • Walk โ€” to the mounting point, 2 m
  • Bend down โ€” reach floor level
  • Reach by hand โ†’ Take / Grasp โ†’ Install / Place โ€” bracket
  • Rotate โ€” tighten fastener
  • Straighten up โ€” return to standing

Body-motion microelements (Bend/Straighten, Sit/Get up) carry no factors โ€” their time is fixed. Include them whenever the posture change physically happens; omitting them understates cycle time.


Machine time with operator overlap

Scenario โ€” operator waits while a CNC finishes cutting, but can unload the previous part.

  • Machine time โ€” autonomous cycle, measured duration
  • Manual microelements (grasp, move, release the previous part) โ€” inside the same Action with overlapped employment enabled

The overlap coefficient determines how much manual time runs in parallel with the machine. If the operator has nothing to do during the cycle, add a Delay element instead.

Think of microelements as vocabulary. Individual motions are letters โ€” it is the sequence within an Action that forms a word with meaning.